Contraction stress build‐up of anisotropic conductive films (ACFs) for flip‐chip interconnection: Effect of thermal and mechanical properties of ACFs

The important mechanical mechanism for the electrical conduction of anisotropic conductive films (ACFs) is the joint clamping force after the curing and cooling processes of ACFs. In this study, the mechanism of shrinkage and contraction stress and the relationship between these mechanisms and the thermomechanical properties of ACFs were investigated in detail. Both thickness shrinkages and modulus changes of four kinds of ACFs with different thermomechanical properties were experimentally investigated with thermomechanical and dynamic mechanical analysis. Based on the incremental approach to linear elasticity, contraction stresses of ACFs developed along the thickness direction were estimated. Contraction stresses in ACFs were found to be significantly developed by the cooling process from the glass‐transition temperature to room temperature. Moreover, electrical characteristics of ACF contact during the cooling process indicate that the electrical conduction of ACF joint is robustly maintained by substantial contraction stress below T_g. The increasing rate of contraction stresses below T_g was strongly dependent on both thermal expansion coefficient (CTE) and elastic modulus (E) of ACFs. A linear relationship between the experimental increasing rate and E × CTE reveals that the build‐up behavior of contraction stress is closely correlated with the ACF material properties: thermal expansion coefficient, glassy modulus, and T_g. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2634–2641, 2004     

变性淀粉取代聚乙烯醇生产Al2O3刚玉陶瓷的胶粘剂研究

论述了变性淀粉取代聚乙烯醇(PVA)生产Al2O3刚玉陶瓷的意义及聚乙烯醇结构与吸附性能的关系，并且根据胶粘机理，通过分析Al203胶粒的表面特性和变性淀粉的结构，说明了变性淀粉可以取代聚乙烯醇。     

Study on the properties of crosslinking of poly(ethylene oxide) and hydroxyapatite–poly(ethylene oxide) composite

This study covers the crosslinking of poly(ethylene oxide) (PEO) and its composite with calcium hydroxyapatite (HA), their mechanical and swelling properties, and morphology. Sheets of the composites of PEO (two different grades with M_v: 5 × 10⁶ and 2 × 10⁵) and HA and neat PEO were prepared by compression molding. The prepared composite and PEO (0.1‐mm‐thick) sheets were crosslinked with exposure of UV‐irradiation in the presence of a photoinitiator, acetophenone (AP). This simple method for crosslinking, induced by UV‐irradiation in the presence of AP, yielded PEO with gel content up to 90%. Gel content, equilibrium swelling ratio, and mechanical and morphological properties of the low molecular weight polyethylene oxide (LMPEO)–HA crosslinked and uncrosslinked composites were evaluated. Although the inclusion of HA into LMPEO inhibits the extent of crosslinking, the LMPEO–HA composite with 20% HA by weight shows the highest gel content, with appreciable equilibrium swelling and mechanical strength. The growth of HA in simulated body fluid solutions on fractured surfaces of LMPEO and also LMPEO–HA was found to be very favorable within short times. The dimensional stability of these samples was found to be satisfactory after swelling and deposition experiments. The good compatibility between the filler hydroxyapatite and poly(ethylene oxide) makes this composite a useful tissue‐adhesive material. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 488–496, 2003     

Studies on polyacrylates containing pendant ligand with carbonyl and hydroxyl functions and their divalent metal complexes

A series of monomers were prepared by reacting (meth)acryloyl chloride with 2,4‐dihydroxybenzophenone, 2,4‐dihydroxybenzaldehyde, and 2,4‐dihydroxyacetophenone, respectively. The monomers were polymerized in dimethylformamide (DMF) at 70°C using benzoyl peroxide as an initiator. Polymer–metal complexes were obtained from DMF solutions of polymers with an aqueous solution of metal ions. The polymers and polymer–metal complexes were characterized by elemental analysis and spectral studies. The IR spectra of these complexes suggest that the metals are coordinated through the oxygen of the carbonyl group and the oxygen of the phenolic–OH group. The electronic spectra, electron paramagnetic resonance (EPR) spectra, and magnetic moments of polychelates showed an octahedral and square planar structure for Ni(II) and Cu(II) complexes, respectively. X‐ray diffraction studies revealed that polychelates are highly crystalline. The thermal and electrical properties, catalytic activity, and structure–property relationships are discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2083–2090, 2003     

Compounding and injection molding of polybutene‐1/polypropylene blends

The effect of shear‐controlled orientation injection molding (SCORIM) was investigated for polybutene‐1/polypropylene blends. This article reports on the methods and processing conditions used for blending and injection molding. The properties of SCORIM moldings are compared with those of conventional moldings. SCORIM is based on the application of specific macroscopic shears to a solidifying melt. The multiple shear action enhances molecular alignment. The moldings were investigated with mechanical tests, differential scanning calorimetry studies, and polarized light microscopy. The application of SCORIM improved Young's modulus and the ultimate tensile strength. The gain in stiffness was greater for higher polybutene‐1 content blends. A drastic decrease in the strain at break and toughness was observed in SCORIM moldings. The enhanced molecular orientation of SCORIM moldings resulted in a featureless appearance of the morphology. Interfacial features due to segregation were visible in the micrographs of SCORIM moldings. Both conventional and SCORIM moldings exhibited form I′ in polybutene‐1. This article explains the relationship between the mechanical properties and micromorphologies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 806–813, 2003     

基于启发式搜索与预标注的中文CCG句法分析

针对中文组合范畴语法(CCG)分析困难的特点,研究如何将两种彼此相互独立的技术共同应用在中文CCG句法分析上。首先使用预标注算法,使用对数线性模型通过去除那些概率较低的词汇范畴来对句子的潜在分析空间进行剪枝。然后应用启发式搜索算法进一步加速分析过程。最后从时间效率和分析精度两个维度对所使用的方法进行验证。实验表明,基于启发式搜索与预标注的句法分析算法可以显著地提高分析效率与分析精度。     

Surface‐initiated atom transfer radical polymerization from Mg(OH)2 nanoparticles to prepare the well‐defined polymer‐Mg(OH)2 nanocomposites

Well‐defined polymer‐Mg(OH)₂ nanocomposites were prepared by atom transfer radical polymerization (ATRP). The ATRP initiators were covalently attached to the Mg(OH)₂ by esterification of 2‐chloropropionyl chloride with hydroxyl group. The amount of polymer grafted from Mg(OH)₂ can be controlled using a different catalyst system and adding a small amount of polar solvent. The well‐defined diblock copolymer, consisting of poly(styrene) (PS) and poly(methyl methacrylate) (PMMA) were synthesized. The products were characterized by nuclear magnetic resonance, Fourier transform infrared, differential scanning calorimetry, and thermal gravimetric analysis. The morphologies of PS/PMMA and PS/PMMA/Mg(OH)₂‐g‐PS‐b‐PMMA blends are compared by using a scanning electron microscope. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3680–3687, 2007     

4-甲氧基苯乙腈的又一种合成法

以4-羟基苯乙酰胺为原料,经甲基化和脱水两步反应合成了4-甲氧基苯乙腈,总收率76.5%。     

Structure of Atomic and Molecular Adsorbates on Low-Miller-Index ZnO Surfaces Using X-ray Absorption Spectroscopy

We review our X-ray absorption spectroscopy studies of adsorbate geometries on the O-terminated (000 ) and Zn-terminated (0001) basel faces, as well as the non-polar (10 0) prism face of ZnO. Studies employing near-edge X-ray absorption fine-structure (NEXAFS) and surface X-ray absorption fine-structure (SEXAFS) are included.     

Effects of an organic phosphorus nucleating agent on crystallization behaviors and mechanical properties of poly(propylene)

The effects of an organic phosphorus nucleating agent on the crystallization behavior and mechanical properties of poly(propylene) were investigated. As the concentration of nucleating agent increased from 0 to 0.8%, the tensile and flexural strengths of the nucleated poly(propylene) resin increased by 15%, the flexural modulus increased by 35%, the crystallization peak temperature increased by 10°C, and the nucleation density (calculated with the nonlinear Voltrra integral equation) increased by 10⁶ times. Mechanical properties increased with nucleation density. Linear equations between the mechanical properties and the logarithmic nucleation density were revealed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 297–301, 2003